Differences

This shows you the differences between two versions of the page.

--- projects:laser_cutter [2020/10/12 07:36] – Midder
+++ projects:laser_cutter [2022/12/03 18:02] – andy
@@ Line 1: / Line 1: @@
 ====== Laser Cutter ======
 ===== Location =====
-  * Next to the high workbench beside window, at front
+  * Next to the 3D Printers
 ===== Hazards ===
@@ Line 11: / Line 11: @@
 ===== Current State =====
-In place but needs above to be completed before operation.
+In place
-===== Current progress =====
-  - Set up again next to window
-  - Cleaned the bed mirrors and Lens, all not in good condition, (rear mirror still to check.)
 ===== TODO =====
-  * Set up Cooling.
+  * Fix laser issue - [[https://lists.57north.org.uk/mailman3/hyperkitty/list/57north-discuss@lists.57north.org.uk/thread/Z4ADFBYKVDTL5YQCNAQZAL7AZIRCH7OS/]]
-  * Air filter,and exhaust outside through window when in use.
-  * computer and software to operate.
-  * Check the bed for focal length of laser
-**Possible**
-  * Better temp control for cooler
-  * Air Assist for the cut, requires air pump.
-  * switch to shut off when door open, or lock.
-  * EMS?
 ===== Notes =====
-  * The hardware is a KH-3020 'Laser Engraving Machine'.
+  * The hardware is a Trotec Speedy100
-  * Dimensions: Width 810mm x depth 510mm x height 260mm (at highest)
+  * The maximum size of a sheet to cut is 610 x 305 mm
-  * The note 'Vinyl: 80mm/s 50%' is written on the machine's body
+  * Typically create designs in [[https://inkscape.org/|Inkscape]]
-  * It is currently water-cooled via water piped though an ice bath.
+  * In your design, use hairline red for cutting and black for engraving
-  * The cut size is approx A4.
+  * The manual [[https://wiki.57north.org.uk/lib/exe/fetch.php?media=projects:operating-manual-speedy-100r-8063-en-us.pdf|operating-manual-speedy-100r-8063-en-us.pdf]]
-  * Ventilation is achieved via a fan and a length of approx 3m of large tubing that exits the machine rear
+  * Service manual {{ :projects:speedy_servicemauual.pdf |}}
-  * A new cooling solution is in development, together with a provision for better ventilation.
+  * The laser cutter is powered by a [[https://www.iradionlaser.com/en/ceramic-co2-laser-tubes/infinity-series-50-120-watt#|Iradion Infinity Series - 50-120 Watt
+The focus guide sits on the laser cutter like so...
+{{:projects:laser_cutter_focus_guide.jpg?400|}}
 ==== Software ====
-We have successfully driven the laser with [[https://www.scorchworks.com/K40whisperer/k40whisperer.html]].
+The software to drive the cutter is on the associated laptop.
+==== Links ====
+  * Some useful notes [[https://edutechwiki.unige.ch/en/Trotec_Speedy_100R]]
+  * Trotec samples and examples [[https://www.troteclaser.com/en-us/learn-support/laser-projects]]
+  *
+===== Photos =====
+{{:projects:laser_cutter_med.jpg}}
-{{tag>project active resources tools infrastructure electronics}}
+{{tag>resources tools making}}